Factory Notes · Structure · Export Shipping
KD vs Fully Welded Display Racks: Which Structure Saves More Shipping Cost?
The KD version costs USD 69.41 at the factory versus USD 64.62 fully welded, but the two loading plans hold 359 and 99 units respectively.
For the same display rack, the knock-down (KD) version costs USD 4.79 more per unit at the factory. Yet its smaller cartons allow far more units in the loading plan. Under the transport budget used below, that leaves KD about USD 39.10 per unit ahead before additional destination assembly and handling.
For KD vs fully welded display racks, compare freight per unit together with factory price and destination assembly. The decision turns on how much assembly and handling are needed after delivery, and what that work costs at the destination.
Comparison assumptions: The calculations below use a USD 6,000-per-container DDP transport budget and USD 45 per worker-hour for illustrative 15-, 30- and 60-minute assembly scenarios; substitute your own freight quote and sample assembly time.
Same Rack, Two Loading Plans


| Comparison item | KD structure | Fully welded structure |
|---|---|---|
| Factory unit price | USD 69.41 | USD 64.62 |
| Carton size (L × W × H) | 168.5 × 55 × 22 cm | 164 × 64 × 69 cm |
| Units per shown loading plan | 359 | 99 |
| Assumed transport budget per plan | USD 6,000 | USD 6,000 |
| Transport allocation per unit | USD 6,000 ÷ 359 = USD 16.71 | USD 6,000 ÷ 99 = USD 60.61 |
| Factory price + allocated transport | USD 86.12 | USD 125.23 |
Figures are rounded to two decimals; differences are calculated before rounding.
Obtain itemized transport quotes on the same destination, trade-term and service basis. Our guide to EXW, FCA, FOB, CIF and DDP explains how to align the scope.
KD reduces the transport allocation by about USD 43.89 per rack. After its USD 4.79 higher factory price, the remaining advantage is USD 39.10 before additional destination assembly and handling.
Why the KD Version Costs More at the Factory
KD is not simply a welded rack with a few welds removed. A joint that the factory could weld directly may instead need a connector, bracket, bolt or nut. The parts must also fit together consistently when the rack is assembled elsewhere.
- Connection parts: brackets, connectors and fasteners add materials and operations.
- Fit and tolerance control: separate parts need a repeatable mating relationship.
- Separated packing: components and hardware may need individual protection and identification.
- Trial assembly: fitting checks help identify missing hardware, interference or unclear assembly steps before shipment.
These requirements can raise production cost even when KD reduces shipping volume. In this example, the increase is USD 4.79 per rack.
How Much Additional Assembly Time Can the Saving Cover?
Measure the additional worker-minutes for KD assembly and handling compared with the fully welded option. Add the working time of everyone involved: two people working for 15 minutes use 30 worker-minutes. Costs common to both options are excluded; any differences in unloading or handling should be added separately.
Additional KD labor cost per rack = additional worker-minutes ÷ 60 × hourly labor-and-handling cost.
Fully welded comparison baseline: USD 125.23 per rack for factory price plus allocated transport.
| Extra labor time | Added labor | KD total | Saving vs welded |
|---|---|---|---|
| 15 min | USD 11.25 | USD 97.37 | USD 27.85 |
| 30 min | USD 22.50 | USD 108.62 | USD 16.60 |
| 60 min | USD 45.00 | USD 131.12 | −USD 5.90 |
Time is additional worker-minutes per rack; a negative saving means KD costs more. Totals and differences are calculated before rounding to two decimals.
At 15 or 30 additional worker-minutes, KD retains a cost advantage. At 60 minutes, the extra labor exceeds the transport-adjusted saving by about USD 5.90 per rack.
The labor break-even point is approximately 52 additional worker-minutes per rack: the USD 39.10 advantage divided by USD 45 per hour, converted to minutes.
Use your own trial assembly result to see which side of that threshold the project falls on. Include any differing rework, missing-hardware handling or installation-support costs in the final comparison.
Ask for Two Comparable Proposals Before Choosing
A useful supplier comparison should include more than two unit prices. Ask for the following in one review:
- Two structure and packing proposals: show the joints, separated components, hardware and carton sizes for KD and fully welded versions.
- Loading quantities and like-for-like transport quotes: use the same container specification, route, destination, trade terms and included services. Confirm that the loading quantity matches the final packaging.
- A sample assembly trial: record worker-minutes, tools and crew requirements. Note where the work happens and include the unpacking and hardware handling that differ between the options.
- Verification against the same requirements: confirm load, stability and appearance, including visible connections.
Our finished-goods inspection checklist provides a reference for dimensions, assembly, appearance and function. Match those checks to the rack's agreed requirements.
A Hybrid Structure Can Be the Next Proposal
If fully welded packing is too bulky but a fully KD design creates too much assembly work, compare a hybrid version. Retain the welded frame where it is needed, and separate the shelves, panels, signage or other components that occupy shipping space.
Run the hybrid proposal through the same packing, assembly and performance comparison. For an example of how packing geometry changes loading quantity, see our wooden-crate loading optimization case.
FAQ
Can I use these per-unit freight figures for a partial-container or LCL shipment?
For a partial-container or less-than-container-load shipment, divide the quote for that shipment by its actual packed quantity. Include minimum charges, consolidation and destination handling in the calculation.
Will the loading quantity stay the same if the packaging changes?
Extra protection, revised cartons, palletization and stacking limits can change the loading quantity. Recheck the loading plan against the final packing specification before ordering.
Compare the Structure Before You Commit to the Packing
At Formost, we compare connections, packing dimensions, container loading and destination assembly together. That shows whether transport savings translate into a real project cost advantage.
Send a drawing or reference photo, target quantity and destination. Formost can review KD, fully welded and hybrid options, then discuss packing, loading quantity and a sample assembly check.
Discuss Your Display Rack Project